Ocean-optics DT1000 Manuel d'utilisateur télécharger pdf

DT-1000 Deuterium Tungsten Halogen Light Source

The DT-1000 DEUTERIUM TUNGSTEN HALOGEN LIGHT SOURCE combines the continuous spectrum of a

deuterium UV light source and a tungsten-halogen VIS/Shortwave NIR light source in a single optical path. The

combined light source produces a powerful, stable output from ~200-1100 nm. It also has a highly stabilized

microprocessor-based power supply designed for optimum stability.

Parts Included

! DT-1000 Deuterium Tungsten Halogen Light Source

! Safety eyewear for protection against dangerous ultraviolet radiation

! Power cord for connecting DT-1000 to outlet

! Allen wrench for adjusting the focus of the collimating lens

Caution!

The beam emerging from the DT-1000 produces visible light and/or invisible ultraviolet radiation. Direct

contact with the beam could cause serious eye injury.

Safety eyewear must be worn at all times while operating the DT-1000. Do not remove any safety

device installed.

Dangerous voltages present.

Only qualified service personnel should service the DT-1000.

This instrument should not be used for any clinical or diagnostic purposes.

Handle with care. Dropping the instrument may cause permanent damage.

For optimum performance below 250 nm, use a solarization-resistant fiber with this lamp.

Operation

Allow several minutes for the lamp to warm up and for the power to stabilize, regardless of the bulb being used.

Best results are obtained after 30 minutes. The spectral output as delivered by an optical fiber will decrease

significantly at wavelengths lower than 250 nm due to attenuation in the lamp envelope, the decrease in detector

efficiency in the spectrometer, and attenuation by the fiber.

1. Put on safety eyewear.

2. Lift the black protective shutter covering the fiber optic port. Install an optical fiber. (For best results, use

our solarization-resistant fibers.)

3. Plug the power cord into the rear of the DT-1000. Plug the other end into a 110 VAC outlet.

4. To turn on the power for the DT-1000, flip the power switch at the rear of the unit, just above where the

power cord connects to the DT-1000. When the power is on, the green Power On light located at the bottom

right of the front panel will light. At this time, the user can now power up the deuterium or tungsten-halogen

source or both. (See the following Operating the Deuterium Source and Operating the Tungsten-

Halogen Source sections for more information.)

5. To turn off the DT-1000, both deuterium and tungsten-halogen sources must be turned off first. Only then

can the user flip the power switch at the rear of the unit to the off position. The green Power On light will

turn off.

6. Lift up the black protective shutter and disconnect your optical fiber from the SMA connector.

Operating Instructions: DT-1000

-1-

1 2 3

Résumé du contenu

Page 1 - Operation

DT-1000 Deuterium Tungsten Halogen Light SourceThe DT-1000 DEUTERIUM TUNGSTEN HALOGEN LIGHT SOURCE combines the continuous spectrum of adeuterium UV l

Page 2 - Bulb Replacement

Operating the Deuterium Source1. To power the deuterium lamp, push in the UV Start button located on the front panel. This white button turnson the de

Page 3 - Specifications

4. Gently grip the top of the bulb and pull it away from the cylindrical unit. Discard the bulb.5. Insert the new bulb into the top of the cylinder, b

Commentaires sur ces manuels

Pas de commentaire

Ocean-optics DT1000 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement Ocean-optics DT1000. Ocean Optics DT1000 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement Ocean-optics DT1000